Merlin Garage Door Opener Troubleshooting Guide

Trouble with your Merlin garage door? When it comes to garage door repair and safety, it is always best to have a professional technician assess the issue. We assess it for free, in most cases the same day, anywhere across Perth. If you would rather take a look yourself first, work through the safe troubleshooting checks below.

  • All Perth covered
  • No call-out fee
  • Same-day service
  • Fixed price before we start

Merlin EVO openers tell you what is wrong with a two-part code. Count the flashes on the UP arrow, then on the DOWN arrow: three then three is code 3-3. On the MR855EVO SilentDrive Pro, the MR550EVO WeatherDrive and the myQ roller door openers the code flashes on LEDs 1 and 3 instead. Find your code below, then work through the checks.

What the lights and beeps mean

On the MT60EVO PowerAce, MT100EVO Tiltmaster and MT120EVO CyclonePro ceiling openers, the code flashes on the UP and DOWN arrows under the access cover. The MR650EVO QuietDrive and MR850EVO SilentDrive roller door openers flash it on the arrows of their control panel. The current Commander myQ ceiling openers use the same arrow codes, and the SilentDrive and WeatherDrive myQ roller openers flash them on LEDs 1 and 3. The meanings below are the same across these models except where noted.

Code 1-1 or 1-2
The safety beam wiring is broken or not connected (1-1), or shorted or wired the wrong way round (1-2). The door will not close and the light flashes.
What to do: Look along the beam wires for staples through them, crushed sections or chewing. Then call us to repair the wiring.
Code 1-3
The wall button or its wiring is shorted, or the button has failed.
What to do: Use a remote in the meantime and call us to check the wall button.
Code 1-4, or 4-6 on the ceiling openers
The safety beams are out of line or were blocked for a moment. The door will not close and the light flashes.
What to do: Clear the beam path, wipe both lenses and gently line the sensors up until both of their lights are steady.
Courtesy light flashes 10 times after the door reverses
The safety beams stopped the door.
What to do: Clear anything in the beam path and try again.
Code 1-5
An internal fault, usually the motor sensor not reporting. The door does not move, clicks, or runs a short way and stops.
What to do: Release the opener and check the door moves freely by hand. If it does and the code returns, call us.
Code 1-6, ceiling openers
The door kept moving after the motor stopped, which can mean a broken spring.
What to do: Stop using the door and call us.
Codes 2-1 to 2-5
An electronic fault inside the opener. On the MR650EVO and MR850EVO, 2-4 means the remote receiver and 2-3 the backup battery.
What to do: Switch off at the power point for 15 to 20 seconds and back on. If the code returns, call us.
Code 3-3, battery light flashing green constantly
A fault in the backup battery's charging circuit.
What to do: Call us. The opener needs a repair.
Codes 4-1 to 4-4
The door stopped or reversed while moving because it is binding, something is in the way, a spring may be broken, the door is locked, or the travel limits need resetting.
What to do: Clear the doorway, make sure any lock is off, then release the opener and move the door by hand. If it binds or feels heavy, call us.
Code 4-5
The opener's travel module is not communicating. The door runs 150 to 200mm, then stops and reverses.
What to do: Call us.
MT3850EVO: orange battery light flashing, a beep every 30 seconds
The backup battery is low. A solid orange light with a beep every 2 seconds means it is running on the battery now.
What to do: Check the power point and switchboard. If the battery light turns red once power is back, the battery needs replacing.

Try these in order

Each check rules out a common cause. Stop as soon as the door runs properly.

Before you start: Merlin's manuals say never to loosen, move or adjust the door, springs, cables, pulleys or brackets: they are under extreme tension. Release the opener with the door closed if you can, keep the doorway clear, and never use the release handle to pull the door open or shut.

  1. 1

    Clear and line up the safety beams

    Find the two sensors either side of the opening near the floor. Move anything between them, wipe both lenses, and look at the small light on each one. On Merlin EVO beams, a steady red light on both means they are lined up, and flashing means they are not.

    What it tells you

    If the lights go steady and the door closes, it was a blocked or knocked beam, codes 1-4 and 4-6. If a sensor stays dark, the wiring is the likely fault.

  2. 2

    Look along the wiring

    Follow the thin wires from the beams and the wall button back to the opener. Look for staples driven through them, sections crushed behind shelving, or chewed insulation. Look only: do not cut or rejoin anything.

    What it tells you

    Damage you can see explains codes 1-1, 1-2 and 1-3, and it is a quick repair for us. If the wiring looks fine, the sensor or the wall button itself may have failed.

  3. 3

    Reset the power

    Switch the opener off at the power point. Wait 15 seconds, or 20 seconds on an MR650EVO or MR850EVO, then switch it back on.

    What it tells you

    Merlin's first step for the 2 codes is a power reset. If the opener runs normally afterwards, it was a one-off. If the same code comes back, the opener's electronics need attention.

  4. 4

    Check the remote, then code it again

    Fit a fresh CR2032 battery. If the remote still does nothing, code it again: hold the remote button, press and release the LEARN button on the opener (yellow on the MT60EVO family, LRN on the MR650EVO and MR850EVO, S on the MR855EVO and MR550EVO), and let go when the opener light flashes.

    What it tells you

    If it works now, it had dropped out of the opener's memory, which happens after power surges. Code 2-4 on a roller opener means the receiver itself has a fault.

  5. 5

    Release it and feel the door

    With the door closed, release the opener: on the MT60EVO and MT100EVO, pull the red rope down once; on the roller openers, pull the cord down firmly until it clicks. Lift the door halfway by hand and let go.

    What it tells you

    Merlin says a door should stay put halfway on its springs and need no more than about 20kg to move. If it is heavy, drops or binds, that is behind codes 1-5 and 4-1 to 4-4, and the springs or tracks need fixing before the opener.

  6. 6

    Turn off Lock on older wall controls

    On older Merlins with a multi-function or LCD wall control, such as the MT3850 and the MJ3800, a flashing push bar or a Locked message means Lock mode is on. Hold the Lock button for 2 seconds to turn it off.

    What it tells you

    Lock blocks the hand-held remotes while the wall button keeps working. If the remotes work once it is off, someone had pressed it by accident.

  7. 7

    Do the monthly safety reverse test

    With the door open, lay a 40mm object flat on the floor in the middle of the doorway, then close the door. It must touch the object and go back up.

    What it tells you

    If it stops on the object instead of reversing, the force and limits need setting again, which we do on site. Do not keep using a door that fails this test.

When to stop and ask us

  • Code 1-6 appears, or the door moves after the motor stops
  • Code 1-1, 1-2 or 1-3 points to damaged wiring
  • A 2 code, 3-3 or 4-5 returns after a power reset
  • The door is heavy, binds or will not stay halfway
  • The battery light stays red after the power is back
  • The safety reverse test fails

Phone 0482 911 999 with the Merlin model on the opener's label and the code you counted. No question is too small.

If it does need a visit

Motor repair visits usually take about 60 to 120 minutes. There is no call-out fee, whether you go ahead or not, and you get one fixed price before any work starts.

  • Full diagnostic of motor, logic board, capacitor and safety circuit
  • Drive gear and sprocket kits fitted for common Merlin and Steel-Line heads
  • Chain or belt tension set and trolley release checked
  • Travel limits and force settings recalibrated
  • Remotes and wall button re-paired and tested
More about motor repair

Merlin Garage Door Opener Troubleshooting, questions we get

Still not sure what is wrong? Phone 0482 911 999 and we will talk it through.

What do the flashing arrows on my Merlin opener mean?

They are an error code in two parts. Count the flashes on the UP arrow, then the flashes on the DOWN arrow: one then four is code 1-4, which means the safety beams are out of line or were blocked. The table on this page covers the codes on the EVO openers we see most in Perth.

My Merlin will not close and the light keeps flashing. What is wrong?

Almost always the safety beams. Codes 1-1 and 1-2 mean the beam wiring is broken or shorted, and 1-4 means the beams are misaligned or something is in the way. Clear the path and wipe both lenses first. If both beam lights are steady and it still will not close, call us.

How do I wipe all the remotes from my Merlin opener?

On the MT60EVO, MT100EVO and MT120EVO, hold the LEARN button until its light comes on and keep holding for about six seconds until it goes out. On the MR650EVO and MR850EVO roller openers, hold LRN for about nine seconds. Then code the remotes you still have, which locks out a lost one.

Why is my Merlin opener beeping every 30 seconds?

On a Merlin with battery backup, such as the MT3850EVO WhisperDrive, a beep every 30 seconds with a flashing orange battery light means the backup battery is low. A red light with beeps after the power returns means the battery needs replacing. Call us and we will test and replace it.

Can I reset the travel limits on my Merlin myself?

Merlin's manuals mention adjusting limits and force, but Merlin itself says technical servicing should be done by a dealer, and every adjustment has to be followed by a safety reverse test. If your door stops short or reverses at the floor, we reset the limits and force and test the reverse before we leave.

Tried the checks and still stuck?

Call and tell us the Merlin model on the opener's label and the code you counted, and we will tell you what it most likely is. No question is too small, and if it does need a visit there is no call-out fee.

Ask a question Call us