Roller Door Spring Replacement and Re-tensioning

A garage roller door that has turned heavy, will not stay up, or slams down at the end of its travel nearly always has a spring problem. Roller door springs are not the torsion spring you see above a sectional door. They are coiled inside the drums at each end of the axle the curtain rolls onto, and most of the time they have lost tension rather than snapped. We re-tension them on the spot, and when a spring has broken or its drum has corroded, garage roller door spring replacement is done the same day.

  • All Perth covered
  • No call-out fee
  • Same-day service
  • Fixed price before we start
What it costs
Priced on the door
Parts and doors vary, so we look first and give you one fixed, fair price before we start.
Time on site
45-120 minutes
Most jobs finished in a single visit.
Call-out fee
None
Whether you proceed with the repair or not.

Signs you need this repair

  • The roller door is heavy to lift by hand and the motor strains on the way up
  • The door will not stay open and creeps back down on its own
  • The curtain slams onto the concrete at the end of its travel
  • One side rolls up faster than the other and the door lifts crooked
  • A bang, then a rattle from the drum at one end of the axle
  • The opener stops partway up and reverses, though nothing is in the way

Where a roller door's springs actually are

Look up at a roller door and you see the curtain rolled onto a barrel, held by a bracket at each side. The axle through the middle of that barrel stays still, clamped to the brackets, and the curtain turns around it on two drums. Inside each drum a coiled spring joins the drum to the axle.

As the door closes, the curtain unrolls and winds those springs up. As it opens, they unwind and do almost all of the lifting, which is why a healthy roller door rises with one hand. B&D Roll-A-Door, Gliderol, Steel-Line and the other roller doors fitted to Perth homes all work this way, even though the parts differ between makes.

Because the springs are inside the drums, you cannot see a break the way you can on a sectional door. The door tells you instead: it turns heavy, drifts, drops or lifts unevenly.

Re-tension or replace: how we tell

Most roller door springs do not break. They relax a little with every cycle until the door is heavy on the way up and quick on the way down. That is a re-tensioning job, and it is the most common roller door repair we do.

A spring that has fractured is different. You often hear it go, and afterwards one side of the curtain is carrying no counterbalance at all, so the door lifts crooked and feels far heavier on that side. Drums that have rusted, cracked or worn their bearings are replaced too, because no amount of tension makes them run smoothly again.

We find out which you have by releasing the opener and lifting the door by hand, then watching where it stops and how each side behaves. That takes a couple of minutes and tells us whether tension alone will fix it.

Re-tensioning a roller door

With the curtain secured and the axle held, we release the clamps at the bracket, add tension a little at a time, and lock the axle again. The door is then tested by hand: lifted to waist height and let go, it should stay where it is, neither drifting up nor sinking.

Once it balances, the opener limits and force are reset, because they were set to suit a door that was heavier than it should be. A motor working against a tired spring is how roller door openers strip their drive gears, so getting the tension right protects the opener as well.

  • Balance tested by hand with the opener released
  • Tension added in small steps and rechecked at half height
  • Opener limits and force reset to suit the corrected balance

Replacing a broken roller door spring

To replace a spring we take the weight of the curtain off the drum, remove the drum and spring, and fit a replacement rated to the width and weight of your curtain. A double roller door carries a much heavier curtain than a single, and the springs have to match it.

Where one spring has broken, the other has done exactly the same number of cycles, so we usually recommend replacing both. You get a door that is balanced evenly from side to side, and you avoid paying for a second visit a few months later.

Shed and workshop roller doors are larger and heavier, and the same rule applies with more force behind it. We re-tension and replace springs on those as well.

Why roller door springs are not a DIY job

The moment the clamps on a roller door axle are loosened, the full tension of both springs is trying to spin the axle. If the tool slips it can spin with enough force to break a wrist, and the curtain can drop at the same time.

What you can safely do is look and listen. Pull the opener's release, lift the door by hand to waist height and let go, then stand back. If it drops, rises or lifts crooked, the springs need attention. Leave the brackets, the axle and the clamps alone, and tell us what the door did.

What the visit includes

  • Door balance tested by hand with the opener released
  • Spring tension adjusted at the axle and rechecked at half height
  • Broken or corroded drum springs replaced to suit the curtain
  • Axle, brackets, clamps and drum bearings checked
  • Side guides cleaned and the curtain checked for creases and wear
  • Opener travel limits and force reset to the new balance

Want it priced first?

Send us the details and we will come back to you with a price. No call-out fee either way.

Roller door springs, your questions

Still not sure what is wrong? Phone 0482 911 999 and we will talk it through.

Can a roller door spring be re-tensioned instead of replaced?

Usually, yes. Most roller door springs lose tension gradually rather than break, and adding tension at the axle brings the door back into balance in a short visit. Replacement is needed when a spring has fractured, or when the drum it sits in has rusted, cracked or worn its bearings.

How do I know if my roller door spring is broken?

A broken spring usually announces itself with a bang, and afterwards the door lifts crooked because one side has lost its counterbalance. A spring that has only lost tension makes the whole door heavy and quick to drop, without the lopsided lift. Either way, stop using the opener and let us look.

How much does roller door spring replacement cost in Perth?

Re-tensioning is the lighter job. Replacing springs depends on the width and weight of the curtain and whether one or both springs need doing, which is why we price your door rather than publish a figure. There is no call-out fee, and you get one fixed price before any work starts.

Can I re-tension my roller door myself?

We strongly advise against it. Loosening the axle clamps releases the full tension of both springs, and an axle that spins out of a spanner or pipe wrench can cause a serious injury. A balance check is safe to do yourself; the adjustment is not.

My roller door motor strips gears. Could the springs be the cause?

Very often. A roller door opener is built to guide a balanced curtain, not to lift a heavy one. When the springs lose tension the motor does the lifting, and the nylon drive gear wears out. Fixing the balance before or alongside the opener repair stops the new gear going the same way.

Do you re-tension shed and workshop roller doors?

Yes. Larger shed and workshop roller doors use the same drum spring design with heavier springs and curtains. We re-tension, replace springs and service the opener on those as well.

Need roller door springs today?

Phone now and tell us what the door is doing, and we will tell you when we can be there.

  • No call-out fee
  • Fixed price before we start
  • Fully insured technicians
Ask a question Call us

Get a quote

Tell us what the door is doing and we will come back to you with a price. If it is urgent, phoning is faster.

The door type, the brand on the motor and your suburb all help us price it properly.

Up to 4. A shot of the door and one of the motor tells us more than anything you can type.

Urgent? 0482 911 999