B&D Roller Door Maintenance and Troubleshooting

Trouble with your B&D garage door? When it comes to garage door repair and safety, it is always best to have a professional technician assess the issue. We assess it for free, in most cases the same day, anywhere across Perth. If you would rather take a look yourself first, work through the safe troubleshooting checks below.

  • All Perth covered
  • No call-out fee
  • Same-day service
  • Fixed price before we start

B&D roller door maintenance takes a few minutes a fortnight and stops most of the faults we are called out for. Below is B&D's own care routine for a Roll-A-Door, what the lights on a Controll-A-Door opener mean, and the checks to work through when the door plays up.

What the lights and beeps mean

The current B&D roller door openers, the Controll-A-Door Power Drive and the Roll-A-Pro, report through four lights under the controls cover: a green OPEN light, a red CLOSE light, a yellow SERVICE light and a red CODE SET light. Older Controll-A-Door R and Controll-A-Door 5 openers flash a two-part code instead: count the red CODE SET flashes, then the red LIMIT SET flashes.

Green or red light keeps flashing, with beeps while the door moves
The door hit something while opening (green) or closing (red).
What to do: Clear the doorway and run the door again. If it was damaged in the hit, call us before using it.
Red CLOSE light keeps flashing with nothing in the way
The opener's travel limits may have been cleared.
What to do: Switch off all power, including any battery backup, and wait 10 to 15 seconds until every light is out. Reconnect. If the red light still flashes, the limits need setting again, which is a job for us.
Green and red lights flashing in turn
The opener is overloaded.
What to do: Pull the release and move the door by hand. If it is heavy or rough, stop using the opener and call us.
Green light flashing rapidly
Mains power was interrupted.
What to do: Check the power point and the safety switch at your switchboard.
Yellow SERVICE light flashing, with a run of beeps
The opener has detected a fault.
What to do: Count the beeps, then press LIMIT SET once to reset. If it comes back, call us and tell us how many beeps you counted.
Yellow SERVICE light on and steady
The opener is due for a service.
What to do: Book a service. Clearing the light is done as part of the service visit.
CODE SET light flashes but the door does not move
The remote button pressed is not the one coded to the door.
What to do: Try the other buttons on the remote.
Older openers: code 1-1, 1-2 or 1-3
The door took too much force to open (1-1), opened too slowly (1-2), or the motor ran over 30 seconds without finishing (1-3).
What to do: Release the opener and check the door moves freely by hand. A heavy or stiff door needs a service and re-tension.
Older openers: code 2-1
The safety beam wiring is shorted or broken.
What to do: Look along the beam wiring for damage, then call us.
Older openers: code 1-4, or 3 and above
A position sensor or electronic fault inside the opener.
What to do: Switch off for 15 seconds to clear the code. If it returns, call us.

Try these in order

The first three are B&D's regular care routine. The rest are for when something has gone wrong. Stop as soon as the door is behaving.

Before you start: Pull the opener's release before cleaning or checking the door, and do it with the door closed if you can. Never touch the brackets at the ends of the roll or the springs inside them: they are under tension, and B&D says only an experienced technician should adjust them.

  1. 1

    Wash the curtain

    Wash the door with clean water and a soft cloth or brush. B&D asks for this every 14 days, and more often within a few kilometres of the coast. Do not forget the top of the roll inside the garage, which rain never reaches.

    What it tells you

    Salt and dust left on the steel are what break down the finish. A door that is washed regularly keeps its coating, and its warranty, far longer.

  2. 2

    Clean the guides, then silicone only

    Wipe the inside of each side guide with a cloth dampened with methylated spirits or mineral turps. Once they are clean, a light silicone spray can go in the guides. Never use grease, oil, WD-40 or RP7 there.

    What it tells you

    If the noise or drag stops, it was grit in the guides. Oil and grease hold that grit and make it worse, which is why B&D rules them out.

  3. 3

    Check how it runs by hand

    With the door closed, pull the opener's release, then open and close the door by hand. B&D asks for this at least every six months. It should take about the same effort each way, and no more than about 20kg on the bottom rail.

    What it tells you

    If it is hard work, check that the felt strips in the guides have not slipped and jammed and that the guides are straight and clean. If it is still heavy after that, the springs need re-tensioning by a technician.

  4. 4

    Read the lights, then reset

    Take the controls cover off the opener and match what the lights are doing to the table above. For a flashing yellow light, count the beeps and press LIMIT SET once. For a red light that keeps flashing, switch off all power for 10 to 15 seconds and reconnect.

    What it tells you

    If the light clears and the door runs normally, it was a one-off. If the same signal comes back, the opener or the door needs a look, and the signal you saw tells us what to bring.

  5. 5

    Check the remote and vacation mode

    Hold a button on the remote: a steady light means the battery is fine, a flashing light or no light means it needs a new CR2032. If no remote works but the wall button does, the opener may be in vacation mode, which shows as a steady CODE SET light. Press the remote button that was set up for vacation mode to turn it off.

    What it tells you

    Power Drive and Roll-A-Pro openers only accept Tri-Tran+ remotes, which have grey buttons and V2 on the back. An older remote will not code to them however many times it is tried.

  6. 6

    Graphite for a stiff lock

    If the key is stiff, puff a little powdered graphite into the keyway. Do not oil or grease the lock and do not take it apart. Always take the key out before opening the door.

    What it tells you

    On a door with an opener, the opener locks the door itself, so the key lock is rarely needed. If you never use it, we can tell you whether it is worth leaving engaged at all.

  7. 7

    Test the safety reverse each month

    Lay a 40mm block of timber, or the opener's box, under the door and close it. The door must touch it and go back up. Then, while the door is opening, take hold of the bottom rail: it must stop.

    What it tells you

    If the door does not reverse or stop, release the opener, use the door by hand only, and call us. A door that will not reverse should not run on the opener.

When to stop and ask us

  • The door still takes more than about 20kg to move after the guides are clean
  • The green and red lights keep flashing in turn
  • A fault code or flashing yellow light comes back after a reset
  • The red light still flashes after a power reset
  • The curtain has come out of a guide or is creased
  • The safety reverse test fails

Phone 0482 911 999 with which lights are on or flashing, how many beeps you counted, and how the door feels by hand. No question is too small.

If it does need a visit

Service and maintenance visits usually take about 45 to 75 minutes. There is no call-out fee, whether you go ahead or not, and you get one fixed price before any work starts.

  • Door balance tested by hand with the opener released
  • Springs, cables, drums and bearings inspected for wear and corrosion
  • Rollers, hinges and tracks checked, adjusted and correctly lubricated
  • Opener force settings and travel limits reset
  • Safety beam alignment and a full reversal test
  • Written note of anything likely to need attention soon
More about service and maintenance

B&D Roller Door Maintenance and Troubleshooting, questions we get

Still not sure what is wrong? Phone 0482 911 999 and we will talk it through.

How often should a B&D roller door be serviced?

B&D's care instructions ask for a professional service every 12 months, more often in harsh conditions such as near the coast, and its warranty terms ask for a service within the first 12 months and at least every two years after that. Between services, wash the door and check how it runs by hand every six months.

What should I lubricate a B&D roller door with?

Only silicone spray in the guides, and only after cleaning them. B&D says never to put grease or oil in the guides or on the felt running strips, and that WD-40 and similar oil-based sprays are not silicone and should not be used. A stiff lock takes powdered graphite, not oil.

Why are the green and red lights flashing in turn on my B&D opener?

On the Controll-A-Door Power Drive and Roll-A-Pro, green and red flashing alternately means the opener is overloaded. Pull the release and move the door by hand. If it is heavy or rough, the springs or guides need attention, so stop using the opener and call us.

My B&D opener's red light keeps flashing. What does that mean?

If the red CLOSE light keeps flashing after any obstruction is cleared, the opener's travel limits may have been cleared. Switch off all power, including any battery backup, wait until every light is out, then reconnect. If the red light is still flashing, the limits need setting again, which is part of a service visit.

Can I adjust the spring tension on my B&D roller door?

No. B&D says spring tension should only be adjusted by an experienced door technician, and the springs inside the drums hold enough energy to injure. If the door has become hard to move after you have cleaned the guides, that is when to book a spring re-tension.

Lights still flashing? Just ask.

Call and tell us which lights are on or flashing, how many beeps you counted, and how the door feels by hand, and we will tell you what it most likely is. No question is too small, and if it does need a visit there is no call-out fee.

Ask a question Call us